Refine your search
Collections
Journals
Year
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z All
L H, Manjunath
- Characterization of Stellite-6 high velocity oxy-fuel coating on titanium alloy
Abstract Views :103 |
PDF Views:0
Authors
Affiliations
1 School of Mechanical Engineering, REVA University, Bangalore 560064, Karnataka, IN
2 School of Applied Science, REVA University, Bangalore 560064, Karnataka, IN
1 School of Mechanical Engineering, REVA University, Bangalore 560064, Karnataka, IN
2 School of Applied Science, REVA University, Bangalore 560064, Karnataka, IN
Source
Journal of Mines, Metals and Fuels, Vol 69, No 12A (2021), Pagination: 20-23Abstract
In the present investigation, cobalt based coating powder namely Stellite-6 was sprayed on titanium alloy (Ti-31) when used in gas turbines by high velocity oxy-fuel method. The microstructure and mechanical properties of the coatings were characterized like coating thickness, density, porosity, surface roughness and micro hardness. The advanced characterization of using advanced microscopy of X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM/ EDX). Followed by fracture toughness of the coating was measured by Palmqvist method. The very good bonding strength between coating and substrate material were identified.Keywords
Fracture toughness, Stellite-6, Ti-31, HVOF, characterization etc.
References
- Sidhu, B.S., Puri, D. and Prakash, S. (2005): “Mechanical and metallurgical properties of plasma sprayed and laser remelted Ni-20Cr and satellite-6 coatings.” Journal of Materials Processing Technology, 159 (3), 347-355.
- Sidhu, T.S., Malik, A., Prakash, S. and Agarwal, R.D. (2007): “Oxidation and hot corrosion resistance of HVOF WCNiCrFeSiB coating on Ni-and Fe-based superalloys at 800ºC.” J. Thermal Spray Technol., 16(5-6), 844-849.
- Oskarsson, H. (2007): “Material challenges in industrial gas turbines.” Proc., of Sino-Swedish Structural Materials Symposium, 11-14.
- Wright, I.G. and Gibbons, T.B. (2007): “Recent developments in gas turbine materials and technology and their implications for syngas firing.” Int. Journal of Hydrogen Energy, 32, 3610-3621.
- Kosel, T.H. (1992): “Friction, lubrication and wear technology.” ASM Handbook, 18, 199-205.
- Heath, G.R., Heimgartner, P., Irons, G. and Miller. (1997): “An assessment of thermal spray coating technologies for high temperature corrosion protection.” Material Science Forum, 251-54, 809-816.
- Sidhu, T. S., Prakash. and Agrawal. (2006): “Hot corrosion resistance of high velocity Oxy-fuel sprayed coatings on a nickel-based superalloy in molten salt environment.” J. Thermal Spray Technol., 15(3), 387-399.
- Niihara, K. (1983): “A fracture-mechanics analysis of indentation-induced palmqvist crack in ceramics.” Mater. Letters, 2, 221-223.
- George, E. Dieter, (1988): “Mechanical metallurgy.” McGrew-Hill book company, Singapore, 11-4, 348-375.
- Effect of beryl and graphene nano platelets reinforcements on the wear behaviour of AL7075- beryl graphene particulate hybrid nano composites
Abstract Views :107 |
PDF Views:0
Authors
Affiliations
1 School of Mechanical Engineering, REVA University, Bengaluru 560 064, IN
2 Aerospae Engineering Department, King Abdulaziz University, Jeddah 21589, SA
3 Aircraft Research and Design Centre, HAL, Bangalore-560037, Karnataka, IN
1 School of Mechanical Engineering, REVA University, Bengaluru 560 064, IN
2 Aerospae Engineering Department, King Abdulaziz University, Jeddah 21589, SA
3 Aircraft Research and Design Centre, HAL, Bangalore-560037, Karnataka, IN
Source
Journal of Mines, Metals and Fuels, Vol 69, No 12A (2021), Pagination: 84-91Abstract
The effect of beryl particles and graphene nano platelets (GNPs) on the wear behaviour of Al7075-beryl-graphene hybrid composites has been studied. The hybrid composites were developed containing Al7075 matrix as matrix materials and 6 weight percentage of beryl and varying 0.5 to 2 weight percentage of graphene by using novel two step stir casting technique and wear behaviour of the newly developed hybrid composites were studied. The dry sliding wear studies conducted using a pin-on-disc tribo-tester under atmospheric conditions revealed that the wear loss of Al7075-beryl-graphene hybrid composites are lower than that of the matrix Al7075 alloy and further with increasing weight percentage of graphene decreased the wear loss of the hybrid composites. The wear studies also showed that the increase in load, sliding speed and sliding distance, the wear loss of the composites increased. The microstructure of the worn out surface revealed that a huge amount of plastic deformation appeared on the unreinforced Al7075 alloy when compared to the reinforced hybrid composites. The incorporation of beryl and graphene into Al7075 showed worn out surface that is not smooth and grooves, scratches and parallel lines were observed. The addition of beryl and GNPs into the matrix reduces erosion and small grooves like structure were noticed in the hybrid composites which leads to a reduction in wear in Al7075-beryl-GNPs hybrid compositesKeywords
Al7075, beryl, graphene, microstructure, wearReferences
- Autar K. Kaw. (2006): Mechanics of Composite Materials, Taylors and Francis, Boca Raton: CRC Press.
- Kainer K.U., (2006): Metal-Matrix Composites. Customs-made materials for automotive and aerospace engineering. Weinheim: Wiley-VCH.
- Clyne TW, Withers P.J. (1993): An introduction to metal matrix composites. Cambridge: Cambridge University Press.
- S. Scudino, G. Liu, K.G. Prashanth, B. Bartusch, K.B. Sureddi, B.S Murthy, and J. Eckert, (1993): “Mechanical properties of of Al-based metal matrix composites reinforced with Zr-based glassy particles produced by powder metallurgy”, Acta Materialia, 57, pp. 2029-2039.
- ASM International: Handbook, Properties and Selection: Nonferrous Alloys and special-purpose materials. 2, 1990.
- Slipenyuk. A, Kuprin V, Milman Y, Goncharuk V, and Eckert J, (2006): “Properties of P/M processed particle reinforced metal matrix composites specified by reinforcement concentration and matrix-toreinforcement particle size ratio”, Acta Materialia, 54, 1, pp. 157-166.
- Abdollah Saboori, Syed Kiomars Moheimani, Mehran Dadkhah, Pavese. M, C. Badini, and Paolo Fino, (2018): “An overview of key challenges in the fabrication of metal matrix nanocomposites reinforced by graphene nanoplatelets”, Metals, 8, pp. 1-25.
- S. Li, B. Sun, H. Imai, T. Mimoto, and K. Kondoh, (2013): Powder metallurgy titanium metal matrix composites reinforced with carbon nanotubes and graphite, Composites Part A: Applied Science and Manufacturing, 48, 57-66.
- Sajjadi, S. A., Ezatpour, H. R., and Parizi, M. T, (2012): “Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 composites fabricated by stir and compo-casting processes”, Materials and Design, 34, pp.106-111.
- Stefania Toschi, (2018): “Optimization of A354 Al-SiCu-Mg Alloy heat treatment, effect on microstructure, hardness, and tensile properties of peak aged and overaged alloy”, Metals, 8, 961.
- N R Prabhu swamy, C S Ramesh, and T Chandrasekhar, (2010): “Effect of heat treatment on strength and abrasive wear behaviour of Al6061-SiCp composites”, Bull. Mater. Sc., 33, 1, pp. 49-54.
- C.S. Ramesh, R. Keshavamurthy, B.H. Channabasappa, and S.Pramod, (2009): “Influence of heat treatment on slurry erosive wear resistance of Al6061 alloy”, Material and Design, 30, 9, pp. 3713-3722.
- Ashok Kumar Sahoo, and Swastik Pradhan, (2013): “Modeling and optimization of Al/SiCp MMC machining using Taguchi approach, “Measurement, 46, pp. 3064-3072.
- Radhika N, Subramanian R, and Venkat Prasat S, (2011): “Tribological behaviour of Aluminum/Alumina/ Graphite hybrid metal matrix composites using Taguchi’s techniques, Journal of Minerals & Materials Characterization & Engineering, 10, 5, pp. 427-443.
- L. Yuan, J. Han, J. Liu, and Z. Jiang, (2016): Mechanical properties and tribological behaviour of aluminum matrix composites reinforced with in-situ AlB2 particles, Tribology International, 98, pp. 41-47.
- Chung D.D.L, (2003): “Applications of composite materials” Composite Materials. Engineering Materials and Processes-Springer, 978, 1, pp. 1-13
- Mohammed Naveed and A R Anwar Khan, “Dry sliding wear of heat-treated hybrid metal matrix composites”, 149, (2016), doi: 10.1088/1757-899X/149/ 1/012084.
- Bhaskar H.B and Abdul Sharief, (2012): “Effect of solutionizing on dry sliding wear of Al2024-Beryl metal matrix composite”, Journal of Mechanical Engineering and Sciences, 3, pp.281-290.
- Md Tanwir Alam, Sajjad Arif and Akhter Hussain Ansari, “Wear behaviour and morphology of stir cast Aluminum/SiC nano composites”, Materials Research Express, (2018), pp.1-25.
- Batluri Tilak Chandra, Sanjeevamurthy, and H.S. Shivashankar, (2017): “effect of heat treatment on hardness of Al7075-Albite particulate composites”, Procedia Materials Science, 4, pp.10786-10791.